|
|
发表于 2013-8-14 10:51:10
|
显示全部楼层
我贴一下我自己收集整理的各个北美普遍率高的刨子品牌的信息，主要是刀片厚度、角度、刨身角度等。可以总结出许多规律的。
- Plane Blades Angle
- Lie-N
- A-2 Steel blades will hold an edge extremely well, especially when sharpened at an angle of 30 degrees
- An O-1 blade will take a slightly finer edge when sharpened at 25 degrees or lower, making them useful for slicing or paring.
- hock
- To strengthen the edge we recommend a larger bevel angle for A2 than we would use for O1. For a bench plane iron, try your A2 blade at about 30° or 33°. A chisel or block plane blade can be even steeper; try 35° or so and see if edge retention is improved.
- Leevalley
- 个别燕尾的刀片是58RC的
- Clip Breaker
- hock
- molding plane，block plane，shoulder plane不需要 breaker。
- 如果用3/16的刀刃，breaker 应该有1/8厚，更薄的刀刃用3/32的breaker，比刀刃短1/2
- 平放离开前端5/8的地方应该有1/16的空隙，角度为25度。
- 离开刀口应该1/64-1/32
- 螺丝口的外端离开刀刃槽的前端应该有3/16的距离。我的螺丝帽是3/8的，螺丝是1/4的，所以槽最好5/16宽。洞的方向很讲究，要让螺丝帽在刀刃上平躺。
- 槽的位置大概在1.5-2.75这里。（3寸半的刀刃）
- lie-N
- 1/8" thick with a .015" lip ground at a 1 degree angle
-
- Normal bench plane:
- 全部配到3／16的厚度。1 1／2到1／ 3／4不等的宽度。全部配breaker
- 大概可以做12个。
- villagecarpenter:
- (1/8)0.125" x 2"
- hock
- all 3/32" thick and 7"long
- 1 3/4" wide (fits #3)
- 2" (fits #4 & 5)
- 2 1/4" (fits some older types)
- 2 3/8" (fits#4½, 5½, 6 & 7)
- 2 5/8" (fits#8)
- Leevalley
- Our bench plane blades are 0.100" thick, All are 7" long with a 30° bevel.
- Blades and Plans for Wooden Planes
- Hock
- 3/16" 0.1875. 厚 come complete with chip-breaker，全部是3½"长的，后来加了4½的。
- 宽度从1到2都有。
- the chip breakers at 1/8" thick.
- davidfinck
- 推荐hock的刀片。
- 1-1/2" -- block planes and jointer planes
- 1-3/4" -- smoothing, jack and jointer planes
- 2" -- smoothing planes (for larger hands).
- Lee Valley Blades for Wooden Planes
- 全部是 3/16" 0.1875. 厚6"宽的，designed to be wedge secured and are used without a chip breaker。从1寸到2-3/8"都有。
-
- Block plane
- 全部选用3／16厚的，1到1.25不等的宽。跟should plane 通用刀片。
- hock
- All are 3/32" （ 0.09375. ）thick x 4 1/4" Long.1 3/8" wide和1 5/8" wide两个尺寸。
- 他们有个木质的特别版本的，没有说厚度，但都是 1" wide blade, 5 3/4" 和3 1/2" long。
- Model Maker's Block Plane
- lie-N
- Blade: 1wide, .125" thick.
- Plane: 4 3/8" long ,1 1/4" The blade sits in the body at 12o.
- Convex Sole Block Plane
- Lie-N
- Blade: 1/8 inch thick , 7/8 inches wide. It has a radius of 7/8 inches, and sits in the body at 20°,
- Plane: The radius across the width of the sole is 3 inches , from end to end the radius is 27 inches. The sole is 3 1/2 inches long and the overall length with the squirrel tail handle is 5 inches.
- The smaller blade radius of 7/8 inches means that the corners of the blade will not protrude from the mouth when set for a medium or fine shaving.
- Violin Maker's Plane
- Lie-N
- Blade: 7/8" wide x 1/8" thick and bedded at 18 degrees.
- Plane: 3 7/16” long x 1 3/16” wide x 1 5/8” tall.
- Block Planes
- lie-N
- Plane: 6¼" long
- Blade: 1-3/8"x 1/8" thick Blade on the Low Angle tool is bedded at 12°, the Standard Angle at 20°. Blades are ground with a 25° flat bevel.
- Skew Block Planes
- Lie-N
- Blade: The l½" x 1/8" The blade sits in the body at 12°; and it comes with a 25° flat ground bevel, making the included cutting angle 37°. The skew angle is 18°.
- Body: 6-7/8" x 1-7/8"
-
- Shoulder Plane
- hock
- The bevel-down blade is bedded at 37.5° for low-angle end-grain planing of shoulders. Our high-carbon, 3/16" thick x 3/4" wide Tee Blade is included.
- 刨子本身的大小：3/4" Iron Width x 10" Length
- Lie-N
- 1/2-Inch Shoulder Plane
- Plane: 5½"
- Blade: ½" wide x 1/8" thick blade. The blade sits in the body at 15°; it comes with at 25° flat ground bevel, making the included cutting angle 40°.
- small
- Plane: 5 3/4” long by 5/8” wide,
- Blade: The blade is .125" (3.55mm) thick, The blade is bedded in the tool at 18° with a 25° bevel, making the included cutting angle 43°.
- The cap and blade bed are intentionally machined so the tip of the cap and blade have excellent contact with the blade bed in the body.
- Medium
- Plane: 7 3/4” long by 3/4” wide
- Blade: 3/4" x .140" thick blade.is bedded in the tool at 18° with a 25° bevel, making the included cutting angle 43°.
- Large
- Plane: 8-1/4" long by 1-1/4" wide
- Blade: 1¼" x .140" thick blade.
-
- Spokeshave Blades
- 全部1／8厚＊3／4宽的刀片，长度自己截。至少可以做4把。
- hock
- 3/32" （0.09375.）thick，0.75-1 宽，没说其他，这是给铁身用的。
- 木身的：
- 1/8"(0.125) X 5/8" X 4 7/16" w/threaded posts 3 15/16" o.c.
- 3/32" X 7/16" X 2 1/2" w/threaded posts 2 1/4" o.c.
-
- Scratch
- hock
- The body measures 3/4" x 1-1/2" x 4-3/4", the blue-tempered spring steel blades are .050" by 3/4 x 1-3/4"
-
- Scraper
- hock
- these blades are 3/32" thick by 2-7/8" wide and 5" long with a 45° bevel on the cutting edge.
- And for the #80 (1/16" X 2-3/4" X 3" long) and the #81 (1/16" X 2-1/2" x 3-7/8" long) Scraper Planes, too!
-
- shooting plane
- Lie-N
- Iron Miter Plane
- Blade: is set in the tool bevel up at 20° with a 25° bevel. 2" x 3/16" thick
-
- Scraping Plane
- small
- Lie_N
- Plane: 5½" long
- blade: 1-3/8" x 1/8" 45° bevel on the blade
- Cabinet Maker's Scraper
- Lie-N
- Plane: Length 8-3/8" Width 2"
- Blade width 2".
- Large Scraping Plane
- Lie_N
- Plane: 9½" long
- Blade: 2-7/8" x .140blade
-
- Flush Plane
- lee valley
- A powerful 1" diameter rare-earth magnet holds the 2" wide blade in place. A steel pin molded into the tough ABS body takes thrust loads. The included blade, with a 25° bevel angle, is readily removed for honing in the usual way.
|
|
楼主: 半匹木马
